catsrest.blogg.se - Smart wall timer switch

#Smart wall timer switch install#
#Smart wall timer switch software#
#Smart wall timer switch password#
#Smart wall timer switch Pc#

This publication contains information that is protected by copyright. The Electromagnetic Compatibility Regulations 2016 (SI 2016 No.1091), The Electrical Equipment (Safety) Regulations 2016 (SI 2016 No.1101), and The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 (SI 2012 No. Is in conformity with the relevant UK Statutory Instruments: Importer: CMS Distribution Ltd: Bohola Road, Kiltimagh, Co Mayo, Ireland.Is in conformity with the relevant Union harmonisation legislation: EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU and RoHS 2011/65/EU with reference to the following standards Standard Version / Issue date EN 55032 2015+A11:2020 class A EN 6 2019 EN 6 2013+A1:2019 EN 55035 2017+A11:2020 EN 62368-1 2014+A11:2017 EN IEC 63000:2018 2018 Declaration of Conformity Address: No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan.Product name: 24+4 Gigabit Combo Switch., office at No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan, R.O.C., declare under our sole responsibility that the product

#Smart wall timer switch software#

This Limited Warranty does not cover any software applications or programs.įor any question, please feel free to contact DrayTek technical support at for further information. A Limited Warranty is offered on DrayTek products. The author of the software does not provide any warranty. This DrayTek product uses software partially or completely licensed under the terms of the GNU GENERAL PUBLIC LICENSE. Please consult the DrayTek web site for more information on newest firmware, tools and documents. ĭue to the continuous evolution of DrayTek technology, all switches will be regularly upgraded. For any questions, please feel free to send e-mail to. If the switch cannot work correctly after trying many efforts, please contact your dealer for further help right away. The home page of VigorSwitch will be shown as below: After configuring correct IP address on your PC, open your web browser and access switch’s IP address.

#Smart wall timer switch password#

Default values of the managed switch are listed as follows: IP Address 192.168.1.224 Subnet Mask 255.255.255.0 DHCP Client Enabled (On) Username admin Password admin

#Smart wall timer switch Pc#

If a PC directly connects to the switch, you have to setup the same subnet mask for PC and the switch. Set up a physical path between the configured the switch and a PC by a qualified UTP Cat.

#Smart wall timer switch install#

Then, install the VigorSwitch (with rack mount kit) on the 19-inch chassis by using other four screws.īefore using the switch, perform the following steps:.

Fasten the rack mount kit on both sides of the VigorSwitch using specific screws.

The switch can be installed easily by using rack mount kit. All device ports are in the same local area network. Use the Ethernet cable(s) to connect None-PoE devices to the Vigor switch. Hardware Installationīefore starting to configure the switch, you have to connect your devices correctly. SFP LNK/ACT Port 25 ~ 28 Port 25 to Port 28 are used for fiber connection. Interface Description RJ 45 LNK/ACT Port 1 ~ 24 Port 1 to Port 24 are used for Ethernet connection. Off The port is disconnected or the link is failed. Combo Ports 25 ~ 28 and SFP (LNK/ACT) On (Green) The device is connected Blinking The system is sending or receiving data through the port. Port 1 ~ 24 On (Green) The device is connected Blinking The system is sending or receiving data through the port. Off The device is not ready or is failed. PWR On (Green) The device is powered on and running normally. Off The power is off or the system is not ready / malfunctioning. Blinking (Green) The switch is powered on and starts system booting. SYS On (Green) The switch finishes system booting and the system is ready.